油浸式變壓器頂層油溫熱路模型計算分析與檢驗
趙蓉1,馮智倩1,高榮貴1,高欣1,許強1,梁嗣元2
1 國網太原供電公司,山西 太原 030012;2 國網電力科學研究院,湖北 武漢 430074
摘 要:介紹了傳統變壓器內部熱場的有限元方法模擬熱路模型,并在此基礎上,增加平均油溫、太陽輻射等條件參數,對原有模型進行改進,利用光纖光柵溫度測量系統,對變壓器樣機進行現場溫升試驗,并將熱路修正模型計算結果與幾臺變壓器實測溫升數據進行對比,結果驗證了該熱路修正模型的精確性。
關鍵詞:變壓器;油浸式;負荷;熱路模型;運行;光纖光柵;溫度測量;油溫
中圖分類號:TM411 文獻標識碼:A 文章編號:1007-3175(2014)02-0056-05
Oil-Immersed Transformer Top Layer Oil Temperature Thermal Circuit Model Calculation Analysis and Test
ZHAO Rong1, FENG Zhi-qian1, GAO Rong-gui1, GAO Xin1, XU Qiang1, LIANG Si-yuan2
1 State Grid Taiyuan Power Supply Company, Taiyuan 030012, China;
2 State Grid Electrical Power Research Institute, Wuhan 430074, China
Abstract: Introduction was made to the finite element method of analog thermal circuit model of traditional transformer internal thermal field,and on this basis, average oil temperature, sun radiation etc conditional parameters were added to carry out improvement for the original model.The optical fiber grating temperature measurement system was used to carry out site temperature rise test for sample transformer. This paper carried out comparison of thermal circuit amended model calculation result with several transformers actual tested temperature rise data. The result verifies the correctness of the thermal circuit amended model.
Key words: transformer; oil-immersed; load; thermal circuit model; operation; fiber grating; temperature measurement; oil temperature
參考文獻
[1] 張強,姚壽廣,馬哲樹. 干式變壓器繞組溫度場的數值計算與分析[ J ] . 華東船舶工業學院學報:自然科學版,2005,19(3):80-83.
[2] 張強. 樹脂絕緣干式變壓器內部溫度場的數值模擬和平均溫升計算方法的研究[ D ] . 鎮江:江蘇科技大學,2005.
[3] 湯焱,劉成遠,郝忠言,等. 變壓器繞組熱點溫升的計算與實驗研究[J]. 變壓器,2001,38(2):1-5.
[4] 劉金澤. 油浸變壓器繞組加導油擋板結構時溫升計算方法[J]. 電機電器技術,2003(5):12-14.
[5] 王緯武. 流體流動與傳熱[ M ] . 北京:化學工業出版社,2002.
[6] 劉鑒民. 傳熱傳質原理及其在電力科技中的應用分析[M]. 北京:中國電力出版社,2006.